Pq Grit Kit 2 Repack !new! File
| Abrasive Type | Mesh Size | Best For | Repack Suitability | | :--- | :--- | :--- | :--- | | (Almandite) | 30/60, 80/120 | General steel cleaning, profile | Excellent (Low dust, recyclable) | | Crushed Glass | 40/70, 70/140 | Soft metals (aluminum), wood | Good (Brittle – use lower air pressure) | | Aluminum Oxide | 24/36, 60/90 | Aggressive etching, coatings | Excellent (Reusable many times) | | Steel Grit (G-40) | G-40 | Peening, thick rust removal | Poor (Too heavy for pneumatic pickup) | | Silica Sand | Any | OSHA prohibited | Never (Risk of silicosis) |
A: Technically yes, but practically no. Mixing 20/40 with 80/120 creates a "binary blend" that causes erratic flow. Stick to one mesh size per repack. Conclusion: Repack Smarter, Not Harder The PQ Grit Kit 2 repack is the single most effective way to reduce your abrasive blasting operating expenses while maintaining peak performance. By following the step-by-step procedure above—inspecting components, choosing the right garnet mesh, and replacing gaskets—you transform a disposable consumable into a permanent asset.
By: Industrial Abrasives Journal
By performing a , you achieve the following: 1. Cost Reduction of 60-80% When you buy bulk abrasive (e.g., a 3,000 lb super sack of garnet at $0.60/lb versus $1.20/lb in kit form) and repack your existing vessel, your cost per blast hour plummets. 2. Reduced Shipping Weight and Freight Costs Empty, the PQ Grit Kit 2 weighs ~35 lbs. Full (with original media), it weighs ~110 lbs. Shipping a full kit requires hazardous material (HazMat) declarations due to the silica potential. A repack is done on-site, eliminating inbound freight on heavy media. 3. Environmental Compliance and Waste Reduction Disposal of a full steel pressure vessel is an environmental burden. Repacking extends the life of the equipment indefinitely. Furthermore, you can repack with recycled media —spent garnet that has been cleaned and screened—creating a closed-loop system. 4. Customization of Grit Size The factory kit comes with one grit size (usually 30/60). But your next job might require 20/40 for aggressive stripping or 80/120 for fine feathering. A repack allows you to tailor the abrasive to the surface profile. Part 3: Step-by-Step Guide to the PQ Grit Kit 2 Repack Performing a repack is a straightforward mechanical procedure, but it requires attention to detail. Incorrect repacking can lead to bridging (where abrasive clogs in the cone), moisture contamination, or deadman valve failure.
Stop paying premium prices for factory-filled kits. Start repacking. Your budget (and your maintenance manager) will thank you. pq grit kit 2 repack
Point the blast nozzle into a test bucket. Engage the deadman. You should see a steady, pulse-free stream of grit. If the flow is erratic, you have bridging (tap the side of the cone) or a jammed metering pin. Part 4: Compatible Abrasives for Your Repack Not all grit is created equal for the PQ Grit Kit 2. The machine’s ceramic-lined nozzle and metering valve are optimized for hard, angular abrasives . Here is your compatibility chart for the PQ Grit Kit 2 repack :
A: The PQ Grit Kit 2 holds exactly 75 lbs of 30/60 garnet (approximately 1.5 cubic feet). Buy a 100 lb bag and keep 25 lbs for top-ups. | Abrasive Type | Mesh Size | Best
Slowly pour your selected grit into the vessel through the top opening. Do not overfill. The PQ Grit Kit 2 has a max fill line etched inside the tank (approximately 3 inches from the top). Overfilling leads to bridging.